Switching Power Supply ATS Model 8000

  • CE Mark
SwitchingPowerSupplyATS
Key Features
  • Open architecture software
    • Expandable hardware support
    • Support GPIB instruments & RS232orRS485/I²C/CAN BUS interface
    • User editable test iteam
    • User editable test programs
    • User editable report format
    • Statistic report
    • On-Line control function
    • User authority control
    • Release control
    • Activity log
    • Master/Slave control mode
    • Multi-UUT test capability for single-output PSU
    • Support barcode reader
    • Support shop-floor control
    • Remote monitoring via internet
  • Test command optimizer helps to improve test speed
  • Capable of coding for any power supply testing applications
  • Comprehensive hardware modules provide high accuracy and repetitive measurements
  • High test throughput by system default test items
  • Microsoft word based evaluation report or UUT characterization
  • Cost effective
  • Other hardware expandable upon request
  • Windows 7/10 or higher based software

The Chroma Power Supply Automatic Test system Model 8000 is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.

The 8000 test system uses a unique test command optimization technology to prevent repetitive control commands from being sent to the system hardware devices. This improve test speed dramatically and makes the Chroma 8000 an ideal choice for both high speed production applications as well as design verification.

The 8000 test system includes a sophisticated test executive which includes pre-written test items covering almost all industry standard power supply tests. User may also create new test items by using a special test item editing function. This gives users the capability to expand the test library unlimitedly.

PowerPro III also includes power full report, statistic and management functions, making the system capable to generate various test documents and per forming system administration. Because the test and statistical reports are critically important in modern factories for R/D evaluation, QA verification and production tests, these functions are an integral part of the system.

Working under Windows 7/10 the model 8000 provides test engineers with a dedicated power supply test system in an easy-to-learn Windows environment and allow access to resources provided by Windows.

  Comprehensive Test Items

The Model 8000 automatic power supply test system comes standard with an off-the-shelf test item library covering most industry standard power supply tests. Unlike traditional ATE software, users do not need to have programming language background to create new test items. Instead the Model 8000 allow users to use pre-compiled test items and to simplify defining test conditions and specifications.

The comprehensive test items cover 7 categories of power supply testing requirements. Output Performances checks the general performances of the UUT. Input Characteristics verifies the input parameters of a power supply. Regulation tests the stability of the UUT under varying linein and loading changes. Timing And Transient measures the transient state during turn-on, turn-off or when events occurred. Portection Tests triggers the protection circuit of the power supply. Finally, the Special Tests and the Special Feature provides means to test the most sophisticated power supplies when unique test routines are needed.

Output Performances

  1. DC output voltage
  2. DC output current
  3. Peak-Peak noise
  4. RMS noise
  5. Current ripple*
  6. Efficiency
  7. In-test adjustment
  8. Power good signal
  9. Power fail signal
  10. P/ S ON signal
  11. Extended measure
  12. Waveform capture
  13. Overshoot voltage

Input Characteristics

  1. Input Inrush current
  2. Input RMS current
  3. Input peak current
  4. Input power
  5. Current harmonics against regulations
  6. Input power factor
  7. Input voltage ramp
  8. Input freq. ramp
  9. AC cycle drop out
  10. PLD simulation

Regulation

  1. Current regulation
  2. Voltage regulation
  3. Total regulation

Timing and Transient

  1. Power up sequence
  2. Power down sequence
  3. Transient response time
  4. Transient spike
  5. Turn ON time
  6. Rise time
  7. Fall time
  8. Hold-up time
  9. Extra timing
  10. Tracking

Protection Tests

  1. Short circuit
  2. OV protection
  3. UV protection
  4. OL protection
  5. OP protection

Special Tests

  1. Fan speed
  2. Correlation test
  3. UUT measurement verification test

Special Functions

  1. Can bus read/ write
  2. I2C read/ write*
  3. GPIB read/ write
  4. RS-232 read/ write
  5. RS-485 read/ write*
  6. TTL signal control
  7. Relay control
  8. Bar code scan*
  9. DMM measure

*These test items need to be created by users by using test item editor due to the variety of the UUTs. And unlimited customized or user defined test items are allowed.

  Software Platform of ATS

The Model 8000 Test Systems include the industries most sophisticated power supply testing software platform, PowerPro III. PowerPro III provides users with an open software architecture suited for a wide range of applications and devices. Power Pro III is a Windows 7/10 environment, which provides necessary computer peripherals.

  Chroma 8000 Applications


▲ Telecom Power Supply

Telecom Power Supply Testing

For the Switching Mode Rectifier or Telecom Power Supply Testing, it should build in other special instruments just like:
RF Voltmeter: It offers measurement with high-input impedance, excellent stability and low noise. It measures the wide band noise of SMR at different frequency.
Transmission Impairment Measurement Set: It offers testing of voice-grade data circuits and metallic digital circuits. It measures the output voltage voice and noise of SMR.


▲ DC-DC Converter

DC to DC Converter Testing

Software: Special Design Test Items (Load Fault Power Dissipation Test, Switching Frequency Test, Synchnization Frequency Test)
Hardware: Create Standard Test Fixture Platform (Receiver)


▲ PV Inverter ATS

Photovoltaic Inverter Testing

The Chroma 8000 ATS is equipped with optimized standard test items for PV inverters (the Unit Under Test), It meets IEEE1547, 1547.1, UL1741, GB/T 19939, CGC/GF004 preliminary test requirements. The user is only required to define the test conditions and specifications for the standard test items to perform the test.

(More Details)


▲ OBC/DC-DC Converter ATS 

EV Power Electronics Testing

For EV On-Board Charger and DC-DC Converter of different UUT characteristics, integrated connecting panel and exclusive test items including basic electrical characteristics and communication protocol test items are provided to shorten the test time greatly.

(More Details)


▲ HCU/DC-DC Converter ATS

EV Power Electronics Testing

It is a customized system based on Chroma 8000 ATS specializing in verification of EV Hybrid Control Unit and DC-DC Converter.

(More Details)


▲ EVSE ATS

EV Power Electronics Testing

It is a customized system based on Chroma 8000 ATS specializing in verification of EV Supply Equipment (EVSE) and complying with SAE-J1772 in programming the test items for operation.

(More Details)

  Chroma Power Supply ATS Version and Windows Version Comparison


Product Inquiry

All specifications are subject to change without notice.
Selection
Model
Description

Switching Power Supply ATS